Power & Pantry

Affiliate disclosure: Power and Pantry is reader-supported. When you buy through links on this page, we may earn a commission from the seller, at no extra cost to you. Commissions never change the math below, and this page states plainly where each brand's program terms differ. Full policy on our About page.

Best folding solar panels for power stations (2026)

By the Power and Pantry editors. Specifications and prices checked at Bluetti's and EcoFlow's own US stores, product pages, datasheets, and user manuals in November 2026. Prices and stock move; the figures below are dated so you can recheck them.

The short answer

Panels are bought by rated watts, but stations accept panels by voltage, current, and connector, and those three numbers decide what you can actually plug in. Read the grid that way and three findings run this page:

The picks that fall out of the grid: for a Bluetti Elite station, two SP200L panels in series (400W, $659.98 for the pair) are the largest clean fit, with one of the new 350W panels as the simpler single-panel option. For an EcoFlow DELTA 3 Classic, two NextGen 220W panels in series (440W) are the largest array that meets all three of EcoFlow's own compatibility conditions. For the two-port stations, one EcoFlow 400W Lightweight per port (800W total) is the straightforward big array. Every one of those statements is worked in the open below.

How this comparison was put together

Every specification and price on this page comes from the two makers' own US stores, product pages, published datasheets, and user manuals, checked in November 2026. Where a maker does not publish a figure, the grid says "not published" rather than borrowing a number from a review site. Daily harvest figures are our own arithmetic from rated watts, with the method and its loss allowance shown in the open. We did not run any of these panels on any of these stations, and no output figure on this page is presented as a bench result.

One reconciliation with our own earlier work, named rather than hidden: our Bluetti vs EcoFlow comparison runs its solar refill check by multiplying rated solar input by four effective sun hours, an input-side figure with no loss allowance. This page's harvest table applies the 14 percent loss allowance EcoFlow itself uses in its published planning method, so the harvest numbers here land lower than a straight multiplication suggests. Both figures are labeled where they appear; this page uses the loss-adjusted version throughout.

The five panels, side by side

PanelRated wattsOpen-circuit voltage (Voc)Working voltage (Vmp)Short-circuit current (Isc)Connector and cableWeightWeather ratingWarrantyPrice, checked November 2026Cost per rated watt
EcoFlow NextGen 160W160W21.3V18.6V9.1AMC4; XT60i charging cable in the box12.3 lbIP6812 months (US)No price on EcoFlow's US product page when checkedNot published
Bluetti SP200L200W24.62V20.52V10.24AMC417.2 lbIP67, splash protection per its manual12 months, per its manual$329.99 (list $399) at Bluetti US, in stock$1.65
EcoFlow NextGen 220W Bifacial220W front, 175W rear21.5V18.4V12.4A frontMC4; XT60i charging cable in the box15.4 lbIP6812 months (US)$449 at EcoFlow US, out of stock in every variant when checked$2.04
Bluetti 350W350W33V27.6V13.8AMC4; 20A MC4-to-XT60 solar charging cable (1.5 m) in the box29.8 lbIP65 per Bluetti's datasheet and the product page FAQ; the same page's body copy says IP67Not published on Bluetti's US product page$649 at Bluetti US; the page lists the panel as shipping January 10$1.85
EcoFlow 400W Lightweight400W (445W under EcoFlow's bifacial BNPI test conditions)39.3V34.5V12.2AFixed integrated XT60 cable, 3.5 m; no MC4 ends22.5 lbIP68Not published on EcoFlow's US product page$699 at EcoFlow US, pre-order shipping late December, out of stock when checked$1.75

Prices and stock from the makers' US stores, November 2026. Electrical figures are each maker's published ratings under standard test conditions: 1,000 watts per square meter of irradiance, an air mass of 1.5, and a cell temperature of 25 degrees C, per EcoFlow's manual for the 400W Lightweight. The Bluetti 350W figures are from Bluetti's own solar panel datasheet for model PV350D, the model whose 33V open-circuit voltage matches the panel Bluetti's US store sells now. Efficiency ratings, for the record: 25 percent for the three EcoFlow panels, up to 23.4 percent for the two Bluetti panels, each maker's own figure.

Matched offers (placeholder). When this site's affiliate programs are approved, this block will list the panels above at the sellers we link to, with prices rechecked at posting. Until then there are no purchase links on this page, and the prices in the grid are the makers' own US store prices from November 2026. If you are sizing panels against a station you have not bought yet, run your appliance list through the generator wattage calculator first: the station size decides how much panel the outage plan can use.

The other half of the fit: the station windows

A panel fits a station when three conditions hold at once. EcoFlow states them in its own DELTA series FAQ: the panel's open-circuit voltage must fall within the station's voltage range, the panel's maximum current must not exceed the station's maximum current, and the panel's maximum power must not exceed the station's maximum power. Bluetti's manuals state the same three limits as panel requirements. These are the windows for the six stations this site compares, from the makers' manuals and US product pages:

StationSolar inputsVoltage windowMaximum currentMaximum solar wattsCable position
Bluetti Elite 100 V2112 to 60V20A1,000WMC4-to-XT60 solar charging cable in the box
Bluetti Elite 200 V2112 to 60V20A1,000WMC4-to-XT60 solar charging cable in the box
EcoFlow DELTA 3 Classic1 XT60i port11 to 60VTotal Isc within 15A, per its manual500WEcoFlow panels include an XT60i cable; other panels need EcoFlow's Solar to XT60 charging cable, from $24.99 at EcoFlow US
EcoFlow DELTA 3 Max Plus2 XT60i ports11 to 60V per portPer EcoFlow's manual for the model500W per port, 1,000W totalSame cable position as the Classic, per port
Bluetti Apex 300212 to 60V per input20A per input1,200W per input, 2,400W totalPV charging cable shipped separately, per its manual
EcoFlow DELTA Pro 32 ports: high-voltage and low-voltageHigh-voltage port 30 to 150V; low-voltage port 11 to 60V15A on the high-voltage port; 20A on the low-voltage port1,600W high-voltage; 1,000W low-voltage; 2,600W totalSame cable position as the Classic, per port

Finding 1: the 8.2-amp limit in Bluetti's manuals

Bluetti's manuals for the Elite 200 V2 and the Apex 300 print a DC input table that the product pages do not mention. In the default (non-advanced) app setting, solar input at a voltage of 30V or below is capped at 8.2A; above 30V the full 20A is available. In the advanced setting, the capped band shrinks to 16V and below. The figure that decides which band a panel lands in is its working voltage, and every single panel in this grid works below 30V except the EcoFlow 400W Lightweight. The arithmetic, at each panel's published working voltage:

Two ways out, both from the same manuals. Wiring two panels in series adds their working voltages: a series pair of SP200L panels works at 41.0V, a pair of NextGen 220W panels at 36.8V, a pair of NextGen 160W panels at 37.2V, all above the band, so a pair draws full current even at the default setting. Or switch the DC input to the advanced setting, where the capped band is 16V and below and the lowest working voltage in this grid is 18.4V, so every panel clears it. Neither fix costs anything. What does not work is buying a bigger single panel for one of these two stations and leaving the setting at default: on the manual's own table, a single 350W panel delivers less into an Elite 200 V2 at default settings than a series pair of 200W panels does.

Scope, stated plainly: this table is printed in the Elite 200 V2 and Apex 300 manuals. We make no claim about the Elite 100 V2 either way, and EcoFlow's manuals print no equivalent band. If your station is one of the two Bluetti models, the setting is worth the minute it takes to check.

Finding 2: the compatibility grid

Series wiring adds voltages and keeps one panel's current. Parallel wiring keeps one panel's voltage and adds currents. Applied to the windows above, within the limits the makers publish, this is what fits:

PanelOn a 60V, 20A input (Elite 100 V2, Elite 200 V2, Apex 300 per input, DELTA Pro 3 low-voltage port)On a 500W, 60V port (DELTA 3 Classic; DELTA 3 Max Plus per port)On the DELTA Pro 3 high-voltage port (30 to 150V)
EcoFlow NextGen 160WTwo in series (42.6V) or two in parallel (18.2A combined Isc) both fit; four as two series pairs in parallel (640W) is the largest array in this grid that fits the windowTwo in series fit (320W, 42.6V); a parallel pair breaks the 15A current rule at 18.2AA single panel's 21.3V sits below the port's 30V floor; a series pair (42.6V) clears it
Bluetti SP200LTwo in series fit (400W, 49.24V); a parallel pair sums to 20.48A of short-circuit current, over the 20A limit on the manuals' current rule, though the pair's combined operating current of 19.5A is under it. Series wiring avoids the questionTwo in series fit (400W, 49.24V); parallel breaks the 15A ruleA single panel's 24.62V sits below the 30V floor; a series pair (49.24V) clears it
EcoFlow NextGen 220W BifacialTwo in series fit (440W, 43V); a parallel pair breaks the current limit at 24.8A combined IscTwo in series fit all three of EcoFlow's conditions (440W, 43V, 12.4A); parallel breaks the 15A ruleA single panel's 21.5V sits below the 30V floor; a series pair (43V) clears it
Bluetti 350WOne panel. Two in series reach 66V, over the window; two in parallel reach 27.6A combined Isc, over the limitOne panel (350W of the port's 500W); a pair fails on voltage in series, on current in parallel, and on watts either wayThree in series fit (99V, 1,050W). Four reach 132V, which fits only where winter lows stay above about minus 5 degrees C; the cold check is below
EcoFlow 400W LightweightOne panel. Two in series reach 78.6V; two in parallel reach 24.4A combined IscOne panel per port (400W of 500W)Three in series calculate to 117.9V and stay under 150V even at the coldest correction factor, but see the cable note below: in practice this panel is a one-per-port product today

The cold check. A panel's open-circuit voltage rises as the panel gets colder, and the highest voltage a station will ever see arrives on the coldest bright morning of the year. The National Electrical Code's correction table for crystalline panels (Table 690.7(A)) multiplies rated voltage by 1.12 just below freezing, 1.20 at about minus 25 degrees C, and 1.25 at minus 40 degrees C. Run the series pairs through it: the 160W pair (42.6V) and the 220W pair (43V) stay under a 60V limit at every factor, reaching 53.3V and 53.8V at the extreme. The SP200L pair (49.24V) reaches 59.1V at the minus 25 factor, under the limit with about a volt to spare, and 61.6V at the minus 40 factor, over it. Two SP200L panels in series are the right wiring in most of the country and the wrong wiring at the coldest sites in it, and no product page in this category tells you that. On the high-voltage port, four 350W panels in series (132V) reach 147.8V at the just-below-freezing factor and about 150.5V one band colder, which is why the grid above calls three the cold-safe count and four a mild-winter option.

The cable note. The 400W Lightweight's cable is fixed to the panel and ends in an XT60 plug: there are no MC4 ends to wire a series or parallel string with, and EcoFlow's own store notes that extension cables and series or parallel accessories for its lightweight panels will be available later in 2026. Until they are, the Lightweight connects one panel to one port, whatever the voltage math allows. The other EcoFlow panels and both Bluetti panels use MC4 connectors, the shared standard in this category, and the cables that bridge MC4 to each station's XT60 or XT60i port are listed in the station table above.

The totals nobody advertises. Add up the largest arrays this grid allows, station by station: the Elite stations, rated for 1,000W of solar input, top out at 640W of these panels wired within the published limits. The DELTA 3 Classic tops out at 440W of its 500W rating. The Max Plus reaches 880W of 1,000W, as a 220W series pair on each port. The Apex 300 reaches 640W per input, 1,280W against a 2,400W rating. Only the DELTA Pro 3's high-voltage port lets folding panels in this grid past 1,000W on one input. The gap is not a defect in any station: it is what happens when panel current ratings meet station current limits, and it is the reason panel shopping by rated watts alone misleads.

Finding 3: real watts against rated watts

The rated wattage on every panel here is a laboratory figure, measured at standard test conditions: full irradiance, a cell temperature of 25 degrees C. EcoFlow's own collection guidance tells buyers to assume a panel produces about 75 percent of its rated power during daylight hours. EcoFlow's published planning method for daily energy applies a 14 percent loss allowance, the default in the National Renewable Energy Laboratory's PVWatts tool: at five peak sun hours, its own worked examples give the 220W panel about 950 watt-hours a day and the 400W panel about 1,720. The arithmetic checks: 220 times 5 times 0.86 is 946, and 400 times 5 times 0.86 is 1,720.

This page's planning table uses the same allowance at four effective sun hours, the planning figure our station comparison uses, so the two pages' solar numbers reconcile: each rated watt returns 3.44 watt-hours a day (4 times 0.86).

PanelRated wattsPlanning harvest, watt-hours per day
EcoFlow NextGen 160W160WAbout 550
Bluetti SP200L200WAbout 688
EcoFlow NextGen 220W Bifacial220WAbout 757
Bluetti 350W350WAbout 1,204
EcoFlow 400W Lightweight400WAbout 1,376

Set those figures against the loads this site sizes by. The fridge load is 1,800 watt-hours a day: covering it from panels alone takes about 525 rated watts at this planning rate (1,800 divided by 3.44). The essentials load, 2,535 watt-hours a day, takes about 740 rated watts. Now the compatibility grid bites: 525 watts of these panels cannot be wired into a DELTA 3 Classic at all (its largest fitting array here is 440W), and 740 watts fits only the two-port stations and the DELTA Pro 3. Solar refill is a real part of a multi-day outage plan, but the array that covers a fridge is bigger, and more constrained by wiring limits, than the rated-watt prices suggest. The fridge runtime article works the load side of that trade in full.

One bifacial warning, in EcoFlow's own framing: the NextGen 220W's front rating (220W) and rear rating (175W) are not additive, and its published guidance says not to promise 395W from the pair of figures. The rear side adds energy when the ground behind the panel is bright; it does not add a second panel. The same discipline applies to the 400W Lightweight's 445W figure, which EcoFlow publishes under bifacial test conditions (BNPI): the planning figure is the 400W rating, and the grid and tables here use it.

The five panels, one at a time

EcoFlow NextGen 160W: the only panel here that parallels cleanly

Who it fits: a household building the largest array a 60V, 20A input allows, or topping up a small station with the lightest panel in the grid at 12.3 lb.

Verified strengths. Its 9.1A short-circuit current is the lowest here, which is a wiring advantage, not a footnote: it is the only panel in the grid whose parallel pair (18.2A) stays inside a 20A station limit, and four of them, wired as two series pairs in parallel, make the largest fitting array on the Elite stations and the Apex 300's inputs at 640W. IP68 rating, a 12-month US warranty, an XT60i cable in the box, and 25 percent efficiency, all from EcoFlow's US product page.

Honest limits. EcoFlow's US product page published no price for this panel when checked in November 2026, so the grid prints no cost per watt for it, and any ranking by price has to wait for a figure we can date. At 160W it also takes the most panels, the most stands, and the most storage space to reach a given array size.

Bluetti SP200L: the series-pair panel

Who it fits: a Bluetti Elite or Apex owner wiring the standard two-panel array, and anyone who wants the lowest verified cost per watt in the grid, $1.65 at its maker's store.

Verified strengths. The pair math is its case: two in series give 400W at 49.24V, inside every 60V window here, with working voltage high enough to clear the 8.2A default band in Bluetti's own manuals. In stock at Bluetti US at $329.99 when checked, the only panel in this grid that was simply buyable at its maker's store on the check date. Its manual publishes a full electrical specification, including the 12-month warranty.

Honest limits. The cold check above is this panel's caveat: a series pair calculates to 61.6V at the minus 40 correction factor, over a 60V station limit, so the coldest sites should wire a pair in parallel only where the current rule allows it, or use a single panel per input. Its manual also rates it IP67 for splash protection and says not to leave it in the rain or water for a long time, a weaker weather position than the EcoFlow panels' IP68. At 17.2 lb it is the heaviest of the three smaller panels.

EcoFlow NextGen 220W Bifacial: the EcoFlow pair

Who it fits: a DELTA 3 Classic or Max Plus owner: two in series are the largest array that satisfies all three of EcoFlow's own compatibility conditions on a 500W port.

Verified strengths. The series pair (440W, 43V, 12.4A) fits the Classic outright and a pair per port takes the Max Plus to 880W. The pair's cold-weather voltage stays under 60V at every NEC correction factor. IP68, 12-month US warranty, XT60i cable in the box, and the joint-lightest build among the mid-size panels at 15.4 lb.

Honest limits. It was out of stock in every variant at EcoFlow US when checked, at $449, which is also the highest cost per rated watt in the grid at $2.04. The bifacial rear rating is real but conditional, as the section above states: plan on 220W. And a parallel pair breaks every current limit in the station table, so this panel's arrays are series arrays.

Bluetti 350W: one big panel, and a name to check twice

Who it fits: a household that wants one panel to carry, set up, and store: 350W on a single stand, with the MC4-to-XT60 cable in the box, and the only panel here that strings three and four deep on a high-voltage input.

Verified strengths. On the DELTA Pro 3's high-voltage port, three in series (99V, 1,050W) are the largest single-input folding array in this grid. Its 33V open-circuit voltage clears that port's 30V floor on its own, the only small-count route to the port. At $649 and $1.85 per rated watt it undercuts the EcoFlow 220W pair's cost for similar daily harvest (about 1,204 against 1,514 watt-hours for the pair, so the pair still harvests more).

Honest limits. Three of Bluetti's own statements about this panel need reconciling before its figures mean anything, and the grid reconciles them rather than picking quietly. First, voltage: the current store page and Bluetti's datasheet for model PV350D agree on 33V, and those are the figures this page uses; Bluetti's older 350W materials list 44V (the older PV350's manual) and 46.5V (Bluetti's own blog for the PV350), and Bluetti's datasheet lists a second 350W variant, the SP350L, at 43.8V. A used or old-stock 350W panel is a different electrical product from the one in this grid. Check the label. Second, weather rating: the datasheet and the product page's FAQ say IP65; the same page's body copy says IP67. The grid prints IP65, the figure two of the three statements support. Third, timing: Bluetti's page lists the panel as shipping January 10, so it is a pre-order product on the check date. Add the wiring position: on any 60V window it is a single-panel product, and on Bluetti's own Elite 200 V2 and Apex 300 it is the panel most reduced by the 8.2A default band, at about 226W of 350W until the setting or the wiring changes. Bluetti's US product page publishes no warranty figure for it.

EcoFlow 400W Lightweight: the biggest single panel, one per port

Who it fits: a two-port station owner who wants the largest harvest per setup: one panel per port is 800W and about 2,752 planning watt-hours a day across the pair, enough on paper to cover the essentials load.

Verified strengths. The largest rated watts and the largest planning harvest in the grid, at $1.75 per rated watt. Its 34.5V working voltage is the only one here above the 30V band in Bluetti's manual table, so it is the one panel the 8.2A default cap cannot touch. IP68 per EcoFlow. At 22.5 lb for 400 rated watts, about 17.8 rated watts per pound, it is the lightest way in this grid to move 400 rated watts; the next best figure is the 160W panel's, at about 13 rated watts per pound.

Honest limits. The fixed cable defines it: no MC4 ends, no series or parallel wiring until EcoFlow's promised accessories arrive, one panel per port in practice. It was a pre-order product when checked, shipping late December at $699, out of stock. EcoFlow's US product page publishes no warranty figure for it. And its 445W bifacial test figure is not its rating: the grid plans on 400W.

How we picked, and our interest in the outcome

The grid holds each maker's current folding panels as sold at its US store in November 2026: three from EcoFlow's NextGen line, two from Bluetti's current line. Superseded models were left out, including Bluetti's older PV350 and PV200 and EcoFlow's older 400W panel, because their electrical figures differ from the current panels' and mixing generations in one grid is how buyers get wired wrong; the 350W section above shows what that difference looks like. Rigid roof panels are outside this page's scope: they are a different product with different mounting, and most are sold as site installations rather than station accessories. Panels sold only through marketplaces with no manufacturer data behind them were left out.

Our interest, stated the way this site states things. Bluetti is our anchor affiliate program for power products. Its program pays 5 to 10 percent commission on a 30-day cookie. EcoFlow's program pays 5 percent on a 7-day cookie. The cookie difference is about our link, not about your outage, and it is disclosed here so you can discount for it. The defense against it is the grid itself: every figure needed to re-rank these five panels by your own station, climate, and budget is printed on this page, including the finding that runs against the anchor brand's own stations, the 8.2A default band in Bluetti's manuals, which leads this page because the manuals lead there.

Questions people actually ask

Can I use a Bluetti panel with an EcoFlow station, or the other way round?

Usually, yes, and the check is the three conditions, not the brand badge. Bluetti's panels and EcoFlow's 160W and 220W panels all connect by MC4, the shared standard. EcoFlow's stations take an XT60i plug, so a Bluetti panel needs EcoFlow's Solar to XT60 charging cable (from $24.99 at EcoFlow US) between the MC4 ends and the station; Bluetti's stations take XT60, and their solar cable ships with the station or, for the Apex 300, separately. Then verify the panel's open-circuit voltage sits inside the station's window, its current within the station's limit, and its watts within the station's cap. Both makers publish the same advice about mixing: Bluetti's collection guidance says to wire panels of the same type, rating, and brand together, and not to mix sizes or brands in one string. Cross-brand single panels are a cable question; mixed strings are where the makers tell you not to go.

Why is my 200W panel only showing about 150 to 170 watts?

Two discounts stack. The first is weather and angle: the rating is a laboratory figure, and EcoFlow's own guidance is to expect about 75 percent of it during daylight hours, which puts a 200W panel near 150W in ordinary good sun. The second, if your station is a Bluetti Elite 200 V2 or Apex 300 at its default setting, is the manual's 8.2A cap on input at 30V or below: a single SP200L calculates to about 168W before any weather discount at all. The fixes are in Finding 1: wire a series pair, or use the advanced DC setting. If the station is another model and the sun is good, 150 to 170W from a 200W panel is the rating working as ratings work, not a fault.

Can I wire two panels in parallel to charge faster?

Only where the current math allows it, and in this grid that is a short list. Parallel wiring adds the panels' currents: two NextGen 220W panels sum to 24.8A of short-circuit current, over the 20A limit on Bluetti's 60V inputs and the 15A rule on EcoFlow's DELTA 3 ports. Two SP200L panels sum to 20.48A, over the same 20A limit on the current rule the manuals print. Two NextGen 160W panels sum to 18.2A and fit a 20A input. Everywhere else, series wiring is the doubling that fits, and it doubles voltage instead, which is why the cold check matters.

How many panels can a DELTA 3 Classic take?

Worked from EcoFlow's three conditions against its 500W, 11 to 60V, 15A port: two NextGen 220W panels in series fit all three (440W, 43V, 12.4A). Two SP200L panels in series fit (400W, 49.24V, 10.24A). One 400W Lightweight fits (400W, 39.3V, 12.2A). Two 400W Lightweights fail every way they can be wired: 78.6V in series, 24.4A in parallel, 800W against a 500W cap either way. The Classic's ceiling with these panels is 440W, and the panel that reaches it is the mid-size one, not the largest.

Will cold weather damage my station through the panels?

It can, and the mechanism is voltage, not cold itself. Panel voltage rises as temperature falls, and a series string sized exactly to a station's limit on a mild day can cross it on the coldest bright morning. EcoFlow's manuals put it as an instruction: keep the total open-circuit voltage within the station's range to avoid product damage, and Bluetti's manuals say not to use panels whose open-circuit voltage exceeds 60V on the 60V models. The NEC correction table in Finding 2 is the check: multiply your string's rated voltage by the factor for your coldest expected temperature and compare it with the station's limit before you wire the string, not after.

Can folding panels stay outside in the rain?

By the makers' published ratings: the three EcoFlow panels are rated IP68. Bluetti's 350W is rated IP65 in its datasheet and FAQ. The SP200L's manual rates it IP67 and describes that as protection against water splash, with an explicit instruction not to leave it in the rain or water for a long time. Ratings describe the panel, not the connectors or the station: keep connections seated and the station itself dry and under cover, whatever the panel's rating says.

Safety and responsibility. The hard limit in this category is voltage. Never connect a panel or a string whose open-circuit voltage, corrected for your coldest expected temperature, exceeds the station's published maximum: both makers' manuals tie out-of-spec voltage and current to product damage, and the station's input is the part that pays. Wire only what the manuals for your specific panel and station describe, keep connectors fully seated, and keep stations dry, ventilated, and within their published temperature ranges. Anything beyond plugging panels into a station, roof arrays, combiner boxes, house wiring, belongs to a licensed electrician, the same line our generator safety page draws for transfer switches.

Data basis for this page: Bluetti's and EcoFlow's US stores and product pages (panel prices, stock, and shipping status), Bluetti's solar panel datasheet (model PV350D electrical figures), the Bluetti SP200L user guide (electrical figures, warranty, weather guidance), the Bluetti Elite 200 V2 and Apex 300 user manuals (station windows and the DC input current table), EcoFlow's DELTA 3 Classic user manual and DELTA series FAQ (station window and the three compatibility conditions), EcoFlow's manual for the 400W Lightweight (standard test conditions and electrical figures), EcoFlow's published planning guidance (the 75 percent daylight figure and the PVWatts loss method), and NEC Table 690.7(A) correction factors for crystalline panels, all checked in November 2026. Figures a maker does not publish are labeled not published: EcoFlow's US product page carried no price for the NextGen 160W, no warranty figure for the 400W Lightweight, and Bluetti's US product page no warranty figure for the 350W panel, on the check date. Harvest figures are this site's arithmetic from rated watts with the loss allowance shown on the page. They are planning estimates, not measurements of any panel.