Power & Pantry

Rainwater Catchment for Hawaii Homes: The Complete Guide

A rainwater catchment system collects the rain that falls on your roof, stores it in a tank, and delivers it to your taps through a pump, filters, and a disinfection step. For tens of thousands of Hawaii households it is not a backup. It is the water supply. One rule governs everything in this guide, and it comes from the Hawaii Department of Health: catchment water is water you treat and test yourself, and it is for drinking only after filtration and disinfection. Get the chain of parts right and keep it maintained, and the system Hawaii families have run on for generations does the rest.

Affiliate disclosure: Power & Pantry is reader-supported, and some links on this site are affiliate links that may earn us a commission at no extra cost to you. This article links to the Hawaii Department of Health, to the University of Hawaii CTAHR catchment guidelines, and to our own water storage calculator. See the About page for how we work.

The short answer: the chain runs roof → gutters → leaf screens → first-flush diverter → covered tank → pump → sediment filters → disinfection → tap. Sizing runs on one formula: gallons harvested = roof area in square feet × rainfall in inches × 0.623. A 1,000-square-foot roof in a 100-inch rainfall area makes roughly 62,000 gallons a year before losses. The tank exists to bridge the gaps between rains, which is why Hawaii tanks run to thousands of gallons: for most catchment homes, the tank is the whole water supply, not a reserve. The Hawaii Department of Health (DOH) does not regulate home catchment systems, and it points owners to the University of Hawaii CTAHR Guidelines on Rainwater Catchment Systems for Hawaii and to a screening test for E. coli, turbidity, lead, and copper. This guide follows those two sources throughout.

Why so many Hawaii homes run on rain

CTAHR opens its guidelines with the scale of it: an estimated 30,000 to 60,000 people in Hawaii depend on a rainwater catchment system for their water needs, and the majority of them live on Hawaii Island, in the Puna, Ka'ū, and Hāmākua districts. These are areas where county water lines do not reach. Subdivisions across Puna and Ka'ū, Hawaiian Ocean View among them, were built without county water service, so the roof and the tank are not an alternative to the water system. They are the water system.

That also defines the legal picture, and it is simpler than most people expect. Catchment is legal in Hawaii, and no agency permits or inspects a home system. In DOH's words, "Rainwater catchment systems on individual homes are not regulated by the Department of Health." CTAHR says the same thing from the other side: there are no government agencies overseeing the safety of your catchment system, so the responsibility sits with the owner. What DOH does instead is publish guidance: how to design the system well, maintain it, treat the water, and test it. That guidance, plus CTAHR's guidelines, is the authority this page defers to, and the DOH rainwater catchment page is the one to bookmark.

How much water your roof actually makes

The harvest math rests on one physical constant. One inch of rain falling on one square foot of surface yields about 0.623 gallons of water. CTAHR's guidelines use 0.625, the same figure rounded, and either gives the same planning answer. The formula:

Gallons = roof footprint (sq ft) × rainfall (inches) × 0.623

Two things in that formula trip people up. First, the area is the roof's footprint, the ground area under the eaves, not the sloped surface. A sloped roof catches rain as if it were its own shadow on the ground, so measure eave to eave, length times width. Second, count only the roof area that is actually guttered into the tank.

Two worked examples, both with a 1,000-square-foot roof:

Real harvest is always lower than the formula's gross figure, and CTAHR names the reasons: some rain evaporates, some splashes off the roof or overflows the gutters in hard downpours, the first-flush diverter sends the first wash of every storm aside on purpose, and a full tank overflows what it cannot hold. Treat the formula as the ceiling your system works under, not a promise.

The rainfall spread on one island

Hawaii Island holds both of those examples, which is the single most important fact in catchment planning here. The table below is NOAA station data for 1998, a relatively dry El Niño year, as published in CTAHR's guidelines. Even in a dry year, the windward stations recorded well over 100 inches while the leeward Kona coast recorded a small fraction of that.

Station (NOAA, 1998)DistrictRainfall that year
PāhoaPuna (windward)118.0 inches
Hilo AirportHilo (windward)108.8 inches
Honoka'aHāmākua (windward)107.0 inches
KahukuKa'ū19.2 inches
HōlualoaKona (leeward)17.4 inches
South KonaKona (leeward)10.3 inches

Same island, same year, a tenfold difference. Your address, not the state average, decides whether catchment is a generous supply or a tight one, and it decides your tank size before anything else does.

Sizing the tank: demand on one side, dry spells on the other

Tank sizing is two calculations pulling against each other. The demand side asks how much your household uses. The supply side asks how long your roof and rainfall can go between useful rains. The tank has to cover the worse of the two.

Demand. Catchment households use less water than the national pattern, and CTAHR cites Hawaii studies putting catchment families at about 30 to 50 gallons per person per day, against a national average near 120. CTAHR's own worked estimate for a typical family of four on catchment is about 200 gallons a day. For the emergency-storage version of the same question, one gallon per person per day for drinking and basic hygiene, see our stored water guide and run your household through the water storage calculator. A catchment tank is sized in weeks of full household use, not days of drinking water, which is why the numbers come out so much larger.

Supply. CTAHR's instruction is blunt: understand your area's dry seasons and plan for the worst case, not the average. The tank bridges the gaps between rains, so the question is how many dry weeks your stored water has to cover. CTAHR works the example this way: a family of four with 10,000 gallons stored has roughly 35 to 40 days of water with no rain at all, at catchment household usage rates. That is the shape of Hawaii tank sizing. Tanks in common local use run to thousands of gallons, commonly 10,000 and up in whole-supply homes, because the tank is the reservoir, the buffer, and in dry months the difference between a working home and a water emergency. CTAHR adds a practical footnote: some fire insurance companies require a home to have at least a 10,000-gallon tank, because in catchment country the tank can also be the fire department's water.

The parts, one by one

The roof: the collection surface

Everything the water touches matters, starting here. CTAHR's rule for all system materials is that they be nontoxic and inert, because rainwater is slightly acidic and acidic water leaches chemicals out of what it runs across. The most common catchment roof in Hawaii is galvanized metal painted or enameled with a nontoxic paint. Concrete, terracotta tile, slate, polycarbonate, and fiberglass roofs can also serve. Roof paint must not contain fungicides or other poisons.

What must stay out of the collection path, per CTAHR: anything containing lead, which in older homes can mean lead-based paint, lead flashing, solder, nails, and even gutters. CTAHR's avoid list also covers bare (uncovered) galvanized metal, zinc, asbestos-containing materials, tar, asphalt, and pesticide-treated wood. Two more CTAHR points worth building in: keep the roof pitch relatively low, because a steep roof throws water past the gutters, and let a brand-new roof rinse through its first few rainfalls before connecting it to the tank, so construction dust and fresh-paint residue wash off to the ground instead.

Gutters and screens: the first filters

Gutters should be as inert as the roof. Most commercially installed gutters in Hawaii are seamless aluminum, PVC gutters are also sold, and CTAHR names copper as a poor choice. The gutter run needs a slight continuous slope to the downspout with no low spots: standing water in a gutter collects insects, animals, and decaying leaves, and decaying organic material ruins taste and color and can cause health problems.

Screens over the gutters and at the downspouts keep leaves and large debris out of the tank. They are the cheapest treatment in the whole system and the easiest to neglect: CTAHR notes screens may need cleaning as often as every two weeks, depending on the season and the vegetation overhead. A screen-and-first-flush combination is CTAHR's recommended practice, because the screen stops the large debris and the diverter handles the contaminated first wash that gets past it.

The first-flush diverter: throwing away the dirtiest water

The first water off a roof at the start of a storm is the most contaminated water the system ever sees. Tests cited by CTAHR show it carries the dust, bird and animal droppings, volcanic particles, mold, and pollen that accumulated on the roof since the last rain. A first-flush diverter is a simple device, often just a capped length of pipe off a T-joint, that fills with that first wash and sends it aside; once it is full, the cleaner water behind it flows to the tank. The diverter pipe drains slowly through a small hole or faucet so it is empty and ready for the next storm, and its cap comes off periodically to clear leaves.

How much to divert is a range, not a point: CTAHR reports recommended amounts from 10 to 49 gallons per 1,000 square feet of roof, with dirtier environments (urban, dusty, industrial) calling for the high end. In dry areas that diverted water is a real cost, and CTAHR notes it can be kept for appropriate non-drinking uses rather than wasted.

The tank: where the water lives

Four tank families cover most Hawaii installations. All of them share two CTAHR rules: the liner or material in contact with the water should be food-grade (DOH suggests liners certified by NSF and approved by the FDA), and the tank should have a solid cover, covered in the next section.

Tank typeWhat it isStrengthsTrade-offs
Corrugated steel, linedThe most common tank in Hawaii; about two-thirds of systems in CTAHR's 2010 survey of catchment usersDurable, and its narrower diameter makes covering easier than wide pool-type tanksDepends on its liner, which should be FDA-approved; many are fitted with mesh covers unless a solid cover is added
Polyethylene (plastic)Molded enclosed tanks with solid covers, now manufactured on Hawaii IslandLightweight, easy to clean and to move when empty, available in food-grade materialThe largest potable size is about 4,000 gallons, so an 8,000 to 12,000 gallon system links two or three tanks; sunlight degrades the plastic, so UV protection matters
Ferroconcrete and solid concreteBuilt in place, sometimes as part of the house structure itselfThe most durable class; calcium in the cement reduces the acidity of acid-rain water; readily supports a solid coverCostly to build and not portable; check for cracks after earthquakes; the high pH of concrete tanks can make chlorine treatment less effective
FiberglassMolded enclosed tanks with a fitted coverLightweight and portable when empty; can be made to food-grade specifications, needing no linerRelatively rare in Hawaii; the material must be food-grade and fully cured, and cheap grades may not be suitable for potable water

The budget end of the market is the above-ground swimming-pool style tank. CTAHR treats it cautiously: low cost and limited durability, hard to cover well because of its wide diameter, and its liner must be chosen carefully, since many pool liners contain biocides that do not belong in drinking water. Two layout details apply to every tank type: the intake pipe that feeds the house should draw from above the tank bottom, so it does not pull up sludge and so the water below it stays in reserve, and the overflow pipe needs a screen or flapper, because an open overflow is a door for animals and insects.

The cover: solid, sealed, and dark

CTAHR's position is one sentence: water storage tanks should be completely covered with a solid material. A good cover does four jobs at once. It keeps out sunlight, which limits algae and other growth. It keeps out dirt and airborne particles. It keeps out animals, insects, and the waste they carry. And it keeps the stored water dark and still, which is also mosquito control: mosquitoes breed in exposed standing water, and a sealed tank gives them nothing to breed in. Mesh covers, usually woven polypropylene, are the common shortcut and CTAHR is clear about their limits: mesh lets sunlight, dirt, small insects, and animal waste through, and as it ages and stretches it sags into the water, forming a pond on top of the tank that birds and insects use directly. A sagging mesh cover is, in CTAHR's assessment, close to having an open tank.

Pump and pressure tank: catchment plumbing is ordinary plumbing

From the tank onward, a catchment home works like any other home. A pump draws water from the tank, and because households expect pressurized water, the pump is paired with a pressure tank, check valves, and a pressure gauge. CTAHR notes that most systems also run a coarse filter at the pump, and gives the diagnostic that goes with it: if your water pressure drops or quality falls, that filter is one of the first things to check, because a clogged filter both restricts flow and can force contaminants through.

The treatment train: sediment first, disinfection last

Treatment is a sequence, and the order is the point. CTAHR's summary of the whole subject is that no single method removes every contaminant, so a good system combines methods into a multiple barrier:

  1. Sediment filtration, coarse to fine. Cartridge filters in series, typically starting around 20 microns and stepping down to about 5 microns, take out the particles. Cleaner water at this stage is what makes the disinfection step work.
  2. Fine filtration where the water calls for it. An "absolute 1-micron" filter certified for cyst removal addresses the protozoan cysts, such as Cryptosporidium, that survive chlorination. A 5-micron carbon block helps with smaller microorganisms, and carbon stages handle taste, odor, and many chemicals.
  3. Disinfection. Chlorine or ultraviolet light, covered next. This is the step that makes the water microbiologically safe, and it only works well on water the filters have already cleared.

Chlorine is the older tool and, in CTAHR's account, a proven one: it kills bacteria and viruses, including the bacterium that causes leptospirosis, and it leaves a residual that keeps working in the tank and the pipes. Its limits are equally specific. It does not kill protozoan cysts such as Giardia and Cryptosporidium, which is what the fine filter is for. It dissipates in sunlight, one more reason the tank stays covered. It works poorly in high-pH water above about 8.5, which occurs in some cement tanks, where CTAHR points to ultraviolet instead. And CTAHR is candid that chlorine at tank levels is probably not high enough to kill the rat lungworm parasite, which is why the slug and snail exclusion covered in the safety section matters so much. DOH's suggested starting point for dosing is 2.5 tablespoons of unscented 5% household bleach per 1,000 gallons of water in the tank, mixed thoroughly and re-measured until the free chlorine reads about 0.5 mg/L. CTAHR puts the maintained residual band at roughly 0.2 to 1 ppm and recommends test strips to hold it.

Ultraviolet light is the other main option, and CTAHR describes UV as the most endorsed disinfection method for home use in the United States. A UV unit sits after the filters and inactivates organisms by disrupting their DNA as water flows past the lamp; Class A systems deliver a dose of 40 mJ/cm². Prefiltration is not optional with UV, because an organism hidden behind a particle is an organism the light never reaches, and UV leaves no residual, so it protects the water at the unit and nowhere downstream. The lamp is replaced about once a year and its sleeve wiped clean periodically so the light gets through. Many Hawaii systems run both: chlorine's residual in the tank, UV's polish at the point of entry, filters in front of everything. DOH's own framing is that disinfection, chlorine, ultraviolet, or both, is strongly recommended for catchment water supplies.

Placeholder: matched offers

When this site's affiliate programs are approved, this block will show the catchment parts owners actually replace on a schedule: sediment and carbon cartridges, UV lamps, first-flush diverters, and tank covers and screens, with dated prices.

No affiliate links are live on this page yet, and nothing here is a product endorsement.

Safety, in the Department of Health's own frame

DOH organizes its catchment advice for volcanic activity into three P's, and the frame works for the whole subject: Prevent contamination through frequent, proper maintenance. Protect yourself by treating the water. Provethe first two are working through periodic testing. DOH's line on the third is worth taking at face value: testing is the only way to verify that your treatment and maintenance are working. Catchment water is tested rather than assumed, because a system can look fine and test badly, and the failure modes that matter, lead, bacteria, a slug in the tank, are invisible.

The DOH screening test is specific: a sample taken after all treatment, such as at the kitchen tap, tested by a laboratory certified or approved by DOH for E. coli, turbidity, lead, and copper, against these acceptable levels:

ParameterDOH acceptable level
Turbidity5 NTU or less
E. coliAbsent
Lead0.010 mg/L or less
Copper1.3 mg/L or less

DOH also subsidizes lead and copper testing for individual catchment homes once a year: the owner pays shipping and $25 for the analyses and DOH is billed for the rest, through the participating laboratory named on its catchment page. DOH is careful to say its screening requirements are less rigorous than what regulated drinking water systems face, and that the actions it recommends, appropriately applied, should help assure that a catchment system is safe for domestic use. That is the honest standard: not a guarantee, a practice.

Rat lungworm: a Hawaii-specific reason the cover matters

Rat lungworm disease is caused by a parasitic roundworm, Angiostrongylus cantonensis, whose life cycle runs through rats, slugs, and snails. It is present across Hawaii, and it belongs in a catchment guide for one mechanical reason: the parasite's larvae can leave a slug or snail and persist in water. CTAHR reports the infectious stage surviving at least 21 days outside a drowned slug, and states the conclusion plainly: it is important to keep slugs, snails, and the infectious larvae they carry out of water tanks.

DOH's published prevention steps are practical, and they map directly onto the system this guide describes. Cover water catchment tanks and containers so slugs and snails cannot get in. Keep the system sealed and screened, and keep mollusks and the rats that complete the parasite's life cycle off the roof and out of the system, which is CTAHR's wording of the same instruction. Control slugs, snails, and rats around the home. Filter the water, since filtration is a working layer against larvae in the water, while remembering CTAHR's caution that tank-level chlorine is probably not enough on its own. And on the produce side, DOH advises washing fresh produce carefully under running potable water, leaf by leaf for leafy greens, and not eating raw or undercooked snails, slugs, or freshwater animals that can carry the parasite. None of this is exotic. It is the covered, screened, filtered system, kept that way.

Leptospirosis: the other name on CTAHR's list

CTAHR's guidelines list leptospirosis among the bacterial illnesses associated with catchment water. The bacteria are carried in the urine of infected mammals, and the route into a catchment system is ordinary: an animal urinates on the roof or in the system, and the rain washes it in. This is one of the specific jobs chlorine does well. CTAHR notes that most bacterial and viral pathogens can be eliminated by chlorination, and its summary calls chlorine particularly useful against the bacterium causing leptospirosis. Exclusion first, disinfection second: the same pattern as everything else in this guide.

The maintenance rhythm

A catchment system is not install-and-forget, and its upkeep is a rhythm rather than a project. Every interval below is DOH's or CTAHR's, not ours.

TaskRhythmSource
Clean gutter and downspout screensAs often as every two weeks in heavy leaf seasons; regularly in all seasonsCTAHR
Clear the roof and gutters; trim branches overhanging the roofRegularly, and whenever debris builds upCTAHR and DOH
Open the first-flush diverter cap and clear debris; confirm the drain hole is openPeriodicallyCTAHR
Change the sediment (coarse) filter cartridgeAbout once a month, or per the manufacturer; check it first whenever pressure dropsCTAHR
Replace carbon filter cartridgesEvery 6 to 12 monthsCTAHR
Replace the UV lamp; wipe its sleeve cleanLamp about once a year; sleeve periodicallyCTAHR
If you chlorinate, check the free chlorine residual with test stripsOngoing; hold roughly 0.2 to 1 ppmCTAHR and DOH
Inspect the tank cover, seals, and overflow screenRegularly; repair holes and sagging immediatelyCTAHR
Clean sludge from the tank bottomAbout every three years, more often if the system takes in heavy debrisFederal guidelines, cited by CTAHR
Test the water (E. coli, turbidity, lead, copper)Periodically, through a DOH-certified or approved laboratory; subsidized lead and copper test once a yearDOH

That rhythm now has its own page: catchment system maintenance, with the filter, UV, first-flush, and tank care laid out as a printable schedule, the lamp's silent failure mode explained, and a priced year of upkeep.

Catchment vs the alternatives, for a home without county water

If county water reached your lot, this page would be a hobbyist's curiosity. Where it does not reach, there are three real options, and most off-line Hawaii homes use catchment as the base with one of the others as the backstop.

Hauled water. A tanker truck fills your tank, which is why even the tank siting advice in CTAHR's guidelines includes hauler access. Hauled water is the standard dry spell answer and, in the driest areas, a standing arrangement: CTAHR notes that in Ocean View, tanks are used as much for storage of purchased, trucked-in water as for rainwater collection. The trade-offs are dependence and diligence. Supply tightens exactly when everyone is dry, and CTAHR advises planning ahead and finding a hauler you trust before a drought. On quality, know your source: commercial haulers must hold a Public Utilities Certificate, but CTAHR notes that haulers delivering to private homes are not subject to the health procedures that apply to haulers serving public water systems, while some haulers are DOH-approved, which is worth asking about.

A drilled well. Where groundwater is reachable and suitable, a well trades the rain cycle for a pump and a power bill. It is a regulated build, not a weekend project: Hawaii law (HRS §174C-84) requires a permit from the state Commission on Water Resource Management before well construction begins, and a separate permit before the pump is installed. Depth, yield, and water quality vary by location, and a private well serving one home is not a public water system, so no agency tests its water for you. The owner's testing habit from catchment carries over unchanged.

Catchment itself. The water is free at the margin and the supply renews with the weather. The costs are the system, the maintenance rhythm above, and the dry-spell exposure that tank size and, when needed, a hauled load exist to manage. For the districts CTAHR names, Puna, Ka'ū, and Hāmākua, that trade has been settled by practice for decades.

Questions people actually ask

Is rainwater catchment legal in Hawaii?

Yes. There is no permit for a home catchment system and no agency that regulates one. DOH states that rainwater catchment systems on individual homes are not regulated by the Department of Health, and CTAHR adds that no government agency oversees the safety of your system. Legal and unregulated are not the same as anything-goes in practice: DOH publishes the design, treatment, and testing steps it recommends, and a home that ever needs a loan, a sale, or an insurance policy will meet people who ask whether those steps were followed.

Can you drink catchment water?

Hawaii households do, every day, and the honest version of the answer is: after treatment, and verified by testing. Untreated tank water is not considered safe for drinking, because the tank collects whatever the roof collected. DOH's path to drinking it is the one this guide is built on: follow CTAHR's design guidelines, install certified filtration and treatment, disinfect, and pass the screening test for E. coli, turbidity, lead, and copper at a DOH-approved laboratory. Prevent, protect, prove. A household that skips the third step is assuming, and DOH's whole framework exists because assumption is the failure mode.

What does a dry month do to the math?

CTAHR works this exact example. A roof with 1,296 square feet of catchment area catches about 810 gallons per inch of rain. A family of four using about 200 gallons a day needs about 6,000 gallons a month, which means that roof needs roughly 7.4 inches of rain that month to break even. A dry month that delivers 3 inches delivers about 2,430 gallons against 6,000 used. The difference comes out of the tank, which is the entire reason the tank is sized in the thousands of gallons: a 10,000-gallon tank absorbs that shortfall and several more like it. A dry season, rather than a dry month, is what the hauled-water backstop is for.

Does catchment work on the Kona side?

With honest expectations, partly, and for most Kona-side homes as a supplement rather than the whole supply. Run the formula with the leeward numbers from the table above: a 1,000-square-foot roof under Hōlualoa's 17.4 inches makes about 10,800 gallons a year before losses. One frugal person at catchment usage rates, about 40 gallons a day, uses roughly 14,600 gallons a year. The roof alone does not cover even that, before losses. What does work on the dry side is the combination CTAHR describes in Ocean View: a big tank that catches every gallon the wet weeks offer, frugal fixtures, and hauled water making up the difference. Catchment as one leg of the supply, sized with the formula rather than with hope, is a sound dry-side system. Catchment as the only leg, at leeward rainfall, usually is not.

What about vog and what comes off the roof during volcanic activity?

DOH publishes a specific guidance document for this, "Precautionary Measures for Residential Rainwater Catchment Users During Volcanic Activity," and its instructions are direct. During volcanic activity, temporarily disconnect the gutters feeding the tank. Do not reconnect until the hazards have passed and the ash and debris have been washed off the roof, out of the gutters, and out of the tank. The reason is composition: ash, laze, and Pele's hair have been found to contain various metals and are hazardous to ingest, so the goal is to keep them out of the tank in the first place. DOH also points catchment users to the County of Hawaii Department of Water Supply's emergency spigots as a water source during such periods. Separately, CTAHR notes that volcanic emissions are Hawaii's greatest cause of acid rain, and that acidic rain speeds the leaching of metals from system materials, which is the long-term version of the same point: what falls on the roof becomes part of the water, so the materials rule and the disconnect rule both matter.

Run your own numbers, then go deeper

Three next steps, in order. First, the demand side: the water storage calculator turns your household and your target days into gallons, weight, and a container plan, and the stored water guide explains the one-gallon standard behind it. Second, the supply side: the rainwater catchment calculator takes your roof's footprint and your district's rainfall and returns your annual harvest, a plain verdict on whether it covers your household, and how long your tank carries you with no rain. The formula on this page, gallons = square feet × inches × 0.623, is the whole calculation underneath it. Third, the authorities: DOH's rainwater catchment page and CTAHR's Guidelines on Rainwater Catchment Systems for Hawaii are the documents every claim in this guide traces back to, and they are the right place to go before building, buying, or drinking.

Our data basis: this guide is built from two published authorities, checked on their sites in November 2026, and from arithmetic shown on the page. The regulatory position, the screening test and its acceptable levels, the subsidized lead and copper test, the bleach starting dose, and the volcanic activity precautions are the Hawaii Department of Health's, from its Safe Drinking Water Branch catchment pages. The system design, components, materials, tank types, treatment, and maintenance facts are the University of Hawaii CTAHR's, from the Guidelines on Rainwater Catchment Systems for Hawaii (revised edition, 2020). The harvest constant, about 0.623 gallons per inch per square foot, is the standard conversion; CTAHR uses 0.625. Rainfall figures are NOAA station data for 1998 as published in CTAHR's guidelines, labeled on the page as one dry year, not a climate average. No prices are quoted, because installed system costs in Hawaii vary too much by site and year for a number here to stay honest. No product is presented as tested by us, and nothing on this page replaces DOH and CTAHR guidance for your own system.